ETI | Waveguide Dehydrators, De-icing & Heat Trace System

How can I communicate with my ASM-1 Smart Manifold?

by ETI Staff | Jul 26, 2017 | ASM-1 FAQs

The ASM-1 Smart Manifold can communicate via Ethernet, RS422 and RS232. The Ethernet interface provides the best communications and control of the dehydrator by providing a web based interface. Through this interface, you can monitor the system, change the IP address,...

How do I setup my ASM-1 Smart Manifold?

by ETI Staff | Jul 26, 2017 | ASM-1 FAQs

The setup of the ASM-1 smart manifold can be done with the following steps: Set up the IP configurations for the Netcom’s and the smart manifold (configuration page) Set up the pressure parameters on the Netcom’s and set them for large system operation Netcom...

Why is there a plug in port number 8?

by ETI Staff | Jul 26, 2017 | ASM-1 FAQs

Actually, there isn’t a plug in port number 8, it is a bleed. If you examine it very closely you will notice that there is a small hole in the middle of it. This is used by the Smart Manifold to bleed off pressure if it senses that it is too high and during its...

Can I hook up an older ADH-2ACom or ADH-3Com to the Smart Manifold?

by ETI Staff | Jul 26, 2017 | ASM-1 FAQs

Yes, but then you will need to set the unit’s port as an input with no IP address. The Smart Manifold will monitor it but will have no control over ADH-2ACom or ADH-3Com other than to be able to open and shut its output through the...

Will the Smart Manifold monitor moisture?

by ETI Staff | Jul 26, 2017 | ASM-1 FAQs

No. The Smart Manifold monitors the pressure from each dehydrator and directs it to the appropriate port. Each of the dehydrators is responsible for monitoring its own moisture levels and dealing with it...

Why does the Smart Manifold keep shutting off my output port?

by ETI Staff | Jul 26, 2017 | ASM-1 FAQs

The Smart Manifold runs a series of tests at intervals you determine during the setup process in the test “Parameters and Control” page. One of these is an output kill leak rate. If this rate is set too low or you develop a leak in the system you are feeding on that...

How can I test the snow sensor?

by ETI Staff | Jul 26, 2017 | Snow & Ice Sensors FAQs

The APS-3C and APS-4C controllers utilize the CIT-1 aerial snow sensor, the GIT-1 gutter snow sensor and the SIT-6E pavement snow sensor to detect weather conditions. All three of the sensors work in the same way, they require a temperature below 38 °F (3.33 °C) and...

The controller is oscillating – How do I fix this?

by ETI Staff | Jul 26, 2017 | EUR-5A FAQs

Install a 100K Ohm resistor in-line with the Equipment Ground terminal (19). Disconnect Equipment Ground terminal (18). Grounding The EUR–5A sensor circuits and the EMC inputs are referenced to a common circuit ground. In most situations, this part of the system can...

What are the BEMC connections for?

by ETI Staff | Jul 26, 2017 | EUR-5A FAQs

BEMC stands for Building Energy Management Computer, which can be used to remotely monitor and control the EUR-5A controller. These connections are made to pins 10 through 16. The following diagram will aid in making these connections. See page 9 of EUR-5A manual....

NETCOM red alarm LED is on, how do I find out what is happening and how do I correct it?

by ETI Staff | Jul 25, 2017 | NETCOM FAQs

Establish communications with the NETCOM dehydrator through the Ethernet interface (default IP address from the factory is 192.168.52.9). The default page is the status page and here you will see the alarm/s associated with the alarm LED in the status box. To...

Recent Posts